HYDRO-STOP® PVC WATERSTOP
STANDARD PERFORMANCE SPECIFICATION (SPS) GRADE
CORK JOINTING SYSTEMS Hydro-Stop® PVC Waterstops lead the way in high technology waterstops and comply with international standards.
Hydro-Stop® PVC Waterstops are extruded from specially compounded PVC in accordance with BS2571 and they are designed for use in water retaining and water excluding structures where a positive seal is required for poured in-situ concrete expansion, construction and contraction joints.
Hydro-Stop® PVC Waterstops are designed for use in many types of applications and structures, and are available in a number of different size profiles to suit a project’s requirement.
Hydro-Stop® PVC Waterstops are available in rolls with separate intersections supplied to simplify and minimise on-site fabrication. The waterstop is heat weldable and allows for fast and easy on-site
- A full range of profiles and sizes to suit all types of construction requirements
- Hydro-Stop® PVC Waterstops conform to, and exceed all major international standards
- High quality compounded PVC for long term durability and integrity
- Factory made intersections to simplify and minimise on-site fabrication
- On-site welding equipment is available upon request
- Internal profiles come with factory pre-punched eyelets for easy and secure wire tying to reinforcement
- Ability to withstand high hydrostatic head pressures
AREAS OF APPLICATION
Water retaining structures:
- Water tanks
- Water treatment plants
- Sewage treatment plants
- Swimming pools
- Dams and spillways
- Bund walls
Water excluding structures:
- Underground car parks
- Retaining walls
- Suspended slabs
- Below ground slabs
- Roof & podium slabs
Note: The product’s design and performance, its intended use, installation and final confirmation and approval for
use, must be provided by the project’s Design Engineer and Project Manager.
PACKAGING: 150mm – 20m = 20m roll, 250mm = 15m roll, | 320mm = 12m roll
ROLL WEIGHT: Dependent upon profile type
STORAGE CONDITIONS & SHELF LIFE: 5 years from the date of production if stored properly in original, unopened and undamaged sealed packaging, in dry conditions out of direct sunlight at temperatures between +10°C and +40°C
MATERIAL TYPE: Polyvinyl Chloride (PVC)
WELDING TEMPERATURES: Approximately 190°C – 200°C
SERVICE TEMPERATURE RANGE: -25°C to +70°C
Note: Refer to Cork Jointing Systems’s in house Certificate of Analysis (COA) dated 15/08/2017 for test results pertaining to the above. A COA is conducted on every batch of raw material that is used in the production of Hydro-Stop® PVC waterstops. Independent laboratory test results are also available upon request. Project specific material properties can be custom compounded to suit. Material properties can vary between batches.
Note: Full dimension drawings available upon request
PROFILE WIDTH SELECTION
The width of waterstop depends upon the thickness of the concrete and positioning of the reinforcement. The thickness of the concrete should be greater than or equal to the width of the waterstop profile. Refer to your engineer for further clarification and approval.
CORK JOINTING SYSTEMS recommends the use of its specialised welding equipment for on-site welding which consists of thermostatically-controlled Welding Irons and special Welding Jigs (each type of CORK JOINTING SYSTEMS Hydro-Stop® PVC Waterstop requires its own welding jig to suit the particular shape).
On-site joining is a simple exercise using CORK JOINTING SYSTEMS Heat Welding Equipment comprising of an adjustable Welding Jig and Welding Iron. The ends of the waterstop are cut square and placed into the adjustable Welding Jig, then push the ends of the waterstop against the Welding Iron and bring the two ends together until the molten ends of the PVC fuse. When ordering Welding Equipment, please advise profile
number of the waterstop required.
FACTORY MADE INTERSECTIONS
A wide range of standardised prefabricated intersection pieces are available allowing easy site welding of butt joints to Hydro-Stop® PVC Waterstop junction pieces. Customised pieces can be made to suit. In such cases, drawings must be provided giving exact dimensions and jointing details.
Where shown on the drawings waterstops shall be Hydro-Stop® PVC Waterstop (state profile number required) as supplied by CORK JOINTING SYSTEMS. Provide factory made waterstop fabrications for all changes of direction, intersections and transitions, leaving only straight butt joined splices for on-site
HEALTH AND SAFETY INFORMATION
Joining of PVC Waterstops is performed by heat welding which results in the discharge of hydrogen chloride mist and vapour. In confined spaces or in still air conditions, the use of a ventilation fan or suitable respirator should be used, and the advice and approval of the Site Safety Supervisor is essential. For further information or advice on health and safety precautions, safe handling, storage and correct disposal of products, please refer to the most recent product Safety Data Sheet (SDS), which is available upon request.
The information and the recommendations relating to the application and end use of this product are given in good faith and are based on the information provided by the manufacturer of the product and/or the Company’s current knowledge and experience in connection with the product when properly stored, handled and applied under normal conditions and no liability of final function at the job site is assumed. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability of, or fitness for, particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written and/or oral recommendations, or from any other advice offered by the Company. The Company also has no express or implied knowledge of any particular purpose for which the product is required and any such information given will not be taken into account in the supply of this product. No responsibility or liability by the Company will be accepted for misuse, misreading or derivation from recommended guidelines in respect of this product and the user shall determine the suitability of the product for his intended use and assume all risks and liability in connection therewith. The information contained in our brochure may change at any time without notice. Any use of this product, Hydro-Stop® PVC Waterstop, in any